Jeep JK 1 Ton APEX Rear 14 bolt Truss Swap Kit. The new APEX Truss and Brackets for swapping in aAAM 14 bolt 10.5 rear axle into a Jeep JK Wrangler ('07-'18)Stronger Design, Lighter Weight, Easier Install.A new era has begun with the arrival of the APEX Truss! Artec Industries is proud to announce the next generation of Patent Pending axle trussesThis series of trusses not only builds on our experience as the world leader in axle truss design, it brings it to a whole new level of cost savings, strength, weight savings, simplicity of installation, precision fitment, and complete axle protection never before seen in the industry.The key feature that sets the APEX truss apart is its unique peaked shape top which provides extra rigidity to the whole truss while allowing both a reduction in weight (vs using a thicker material top) and eliminating long weld seams.Previous version with long weld seams which can be lead to extra weld warping of the axle, longer install times and can be inconsistent. Without long seams to weld, now you drop the truss directly on to the axle and weld it to the axle faster.Artec Industries is excited to announce the JK 1 ton APEX Rear 14 bolt Truss Swap Kit. This is an advanced truss and bracket system which can be used for AAM 14 bolt 10.5 inch ring gear.This kit provides the factory link, trackbar, spring, anti-sway bar, bump stop pads and shock locations all encompassed in an axle tube reinforcing truss system. The Sterling axle is a great match to the Superduty Front Dana 60 however there are some considerations to take into account (see below).Features include:Patent Pending APEX Truss peaked top design provides more rigidity than a flat top truss designCNC Precision Laser cut in-house from 1/4 inch and 3/16 inch mild steel for a lightweight yet strong solution...only 42 lbs totalCNC Precision Bent in-house for a great fitment. Literally drop the truss in place on the axle and it's ready to weld. No puzzle piece assemblingDesigned used 3D models directly from Ford and Jeep for not only an amazing fit but clearances with surrounding components70 percent less welding needed than previous truss designs means less warping, faster turnaround, and lower costsAll long seams are bent so you don't need to spend time welding them togetherDimpled holes provide not only weight reduction but rigidity and strengthContours both the cast steel differential and can be welded with normal MIG welder and moderate pre-heating and post-heatingTwo piece truss design means smaller packaging and less shipping costs along with easy installationUsing a 1 ton axle will support larger tires and less chance of breakage in extreme conditionsCoil brackets and bump stop pads are combined to form an axle tube truss and allows for easy installment of other bracketsPrecision CNC cut from 1/4 inch and 3/16 inch steel for high strength and precision and CNC bent for great fitment.Includes all the brackets necessary for a complete axle swap including upper and lower control arm mounts, shock mounts, anti-sway bar mounts, trackbar mount, bumpstop pads and coil spring mounts.Save hours of installation time with the built-in axle tube truss which is quicker to weld than individual bracketsTracbar mount includes 4 locations for those who have aftermarket lifts. Stock height hole is not included though.Coil Spring locator is machined from solid steel making welding to bracket quicker than previous tube and cap style locatorsShock brackets have been moved up for a slightly higher clearance lower control arm bracketEasily upgradeable for future link geometry changes. Just trim off factory location upper control mounts and weld on a center link mount (not included)Important Note for 14 Bolt: The 14 bolt axle is available in a variety of vehicles over several decades. In order for the JK swap to work with factory UCA brackets, the correct width axle must be used. If you are not using factory UCA brackets, but rather a 3-link style system mounted on the truss, you can choose any width axle you need but take care to ensure its width is close to the front axle. Older 14 bolt axles will not work with ABS brackets we offer either.This Kit Is Intended For Use With A Newer Style 14 Bolt Axle With Ribbing On The Casting (As Shown) And Has A Wms-Wms Measurement Of 68 Inch Or Greater.This axle is referred to as an AAM 14 bolt 10.5 inch ring gear and is found in '99-'06 GM 2500 and 3500 SRW trucks. Van axles have a different differential offset and will not align the truss correctly.
- series:
- finish: Bare
- material: Steel
